Please Leave Us A Message
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
How to Install a Hand Held Shower Head in a Tub?
A hand held shower head upgrade is one of the fastest ways to make a tub more practical. It improves rinsing, makes cleaning the tub easier, supports bathing kids or pets, and can help users with limited mobility. Most installations do not require opening the wall, but the correct method depends on your current tub setup. Some tubs have a standard shower arm coming out of the wall. Others only have a tub spout and no shower riser. This guide explains both scenarios, shows the parts you need,...
How Do You Measure a Widespread Faucet?
Measuring a widespread faucet is the fastest way to avoid mismatched hole spacing, handle interference, and installation delays. A widespread bathroom faucet normally uses three mounting points: hot handle, spout, and cold handle. The critical measurements are the hole spread between handles, the reach and height of the spout, and the clearances needed for handles, backsplash, and drain components. This guide shows exactly what to measure on an existing faucet and on the sink or countertop,...
Can You Use a Widespread Faucet on a Centerset Sink?
You can sometimes use a widespread faucet on a centerset sink, but only when the sink hole layout and spacing allow it. In most cases, a true centerset sink has three holes drilled on 4 inch centers, while a widespread faucet set is built for holes spaced farther apart, commonly 8 to 16 inches. If the sink holes are fixed at 4 inches, a widespread faucet usually will not fit without modifying the countertop or replacing the sink. The right approach is to identify what you actually have, then...
How Long Does It Take to Replace a Sink Faucet?
Replacing a sink faucet is often described as a quick upgrade, but the actual time can vary a lot depending on the faucet type, the condition of the existing plumbing, and how much working space you have under the sink. In a clean, modern setup with flexible hoses and accessible mounting hardware, many replacements finish in about an hour. In older bathrooms, the same job can stretch to several hours because of corroded nuts, stuck supply lines, or shutoff valves that do not close reliably....
How to Replace a Bathroom Sink Faucet?
Replacing a bathroom sink faucet is one of the most practical upgrades you can do in a restroom renovation. A new faucet improves daily control, reduces leaks, refreshes the look of the vanity area, and can simplify cleaning around the sink deck. The job is very manageable with standard tools, but success depends on planning around the existing sink hole pattern, supply line condition, and the space available under the basin. This guide walks through the full replacement process from removal to...
How to Fix a Loose Towel Ring?
A loose towel ring is more than an annoyance. It can scratch tile, tear drywall, and eventually pull the mounting plate out of the wall. The fix is usually simple, but the correct method depends on why it loosened in the first place. Some rings wobble because the hidden set screw backed out. Others loosen because the wall anchor is failing, the mounting screws are stripped, or the bracket was installed without enough support behind the wall surface. This guide walks you through fast checks, the...
Towel rings are not out of style. What changed is how designers and homeowners use them. A towel ring used to be the default next to almost every vanity, but today it is chosen more intentionally based on bathroom size, towel-drying expectations, and the overall hardware style. In many modern bathrooms, towel rings remain a clean, space-saving choice for hand towels, especially in powder rooms and compact vanities where a full bar feels bulky. The key is selecting the right ring shape, finish,...
How High to Mount a Towel Bar?
Towel bars seem simple, but mounting height affects daily comfort, towel drying speed, wall cleanliness, and whether the hardware stays tight over time. A bar set too low causes towels to drag the vanity or toilet tank, stay damp, and pick up dust. Too high makes it awkward to reach, especially for children or shorter users. The best height depends on towel size, the wall location, and the bathroom layout. This guide gives practical height ranges used in real projects and explains how to adjust...
Installing a towel bar looks simple, but the difference between a sturdy, long-lasting installation and a bar that loosens over time usually comes down to wall structure, anchoring method, and accurate layout. A properly mounted towel bar should stay level, resist twisting when towels are pulled sideways, and keep the mounting points sealed and protected in humid bathroom conditions. This guide explains how to install a towel bar on common wall types, how to choose the right anchors, how to...
Which Is Better: Touch Faucet or Sensor Faucet?
Touch faucets and sensor faucets both reduce handle use, but they solve different problems. A touch faucet turns on when you tap the spout or body, while a sensor faucet turns on when hands enter an activation zone. In most bathroom sink settings, a sensor faucet is usually the better choice for hygiene consistency, water control, and standardized user behavior. In many kitchen workflows, a touch faucet can feel more intuitive because you can keep the water running while shifting tasks. The...
How to Fix a Motion Sensor Faucet?
A motion sensor faucet is designed for hands-free convenience, but when it stops working it can feel more complicated than a manual tap because electronics and a solenoid valve are involved. In practice, most failures come from a short list of causes: low power, blocked screens, a dirty sensor window, debris in the valve, or unstable water pressure. This guide gives a structured troubleshooting path for bathroom touchless faucets and ties the recommendations to COIGN’s product approach through...
How to Clean a Touchless Sensor Faucet?
A touchless sensor faucet stays cleaner than a manual faucet because fewer hands contact the surface, but it still needs regular care. Water spots, soap residue, and mineral scale can build up on the spout, aerator, and around the sensor window. If those deposits are ignored, the faucet can look dull, the flow can become uneven, and the sensor may misread movement. This guide explains a safe, practical cleaning routine for daily use and for deeper maintenance, with tips that protect finishes...
Do Motion Sensor Faucets Save Water?
Yes, motion sensor faucets can save water, but the real savings depend on how people use the sink and how the faucet is specified and tuned. In most bathrooms, the biggest source of waste is not high flow, it is water running when it is not needed. A sensor faucet addresses that behavior by turning water on only when hands are in the activation zone and turning it off immediately after use. When this is paired with an efficient flow rate, the savings become both measurable and repeatable across...
What Is an Exposed Shower System?
An exposed shower system is a complete shower set where the key waterway components are installed on the finished wall surface rather than hidden inside the wall. The hot and cold supply lines connect to a visible mixer valve, and water is delivered to an overhead shower head, a handheld shower, or both through external pipes and a riser rail. Because the system does not rely on concealed in-wall bodies for most applications, it is widely used for renovations, fast bathroom upgrades, and...
How to Install an Exposed Shower System?
An exposed shower system mounts on the finished wall surface and connects directly to existing hot and cold water outlets. It is a practical option for upgrades because it avoids opening the wall in most cases, and it is also easier to service later since key components remain accessible. The installation quality mainly depends on accurate center-to-center measurement, correct sealing, and stable wall anchoring. COIGN provides exposed shower systems designed for project and residential use. You...
Are All Sink Faucets the Same Size?
No, sink faucets are not all the same size. Even when two faucets look similar in photos, they can differ in mounting hole requirements, spout reach, spout height, handle spread, and connection standards. The right faucet size is the one that matches your sink or countertop drilling, provides comfortable clearance for daily use, and aligns with your plumbing connections without forcing adapters or awkward routing. COIGN supplies both kitchen and basin mixers for residential and project...
What Color Faucet for a Stainless Steel Sink?
Choosing a faucet color for a stainless steel sink is mainly about matching undertones, controlling visual contrast, and selecting a finish that stays consistent under daily use. Stainless steel sinks are usually neutral, but the surrounding countertop, cabinet color, and lighting can make the same sink read cooler, warmer, or more reflective. The right faucet finish should look intentional in the space, resist visible wear, and remain easy to clean. COIGN manufactures kitchen and basin mixers...
How to Clean Sink Faucet Buildup?
Sink faucet buildup is a common problem in kitchens and bathrooms, especially in areas with hard water or frequent daily use. Over time, minerals, soap residue, grease, and water stains accumulate on the faucet surface and internal outlets, affecting both appearance and performance. Proper cleaning not only restores the faucet’s finish but also helps maintain smooth water flow and extend service life. This guide explains what causes faucet buildup, how to clean it safely and effectively, and...
How to Install a Wall Mount Tub Faucet
A wall mount tub faucet is a common choice in modern bathrooms because it creates a clean, uncluttered look and allows greater flexibility around the bathtub area. Unlike deck-mounted faucets, most of its functional components are concealed inside the wall, which makes installation accuracy especially important. This article explains the full installation process in a structured way, combining paragraph-based explanations with clearly defined step sections such as preparation, installation...
A bidet faucet is designed to provide precise water control for personal hygiene, offering a cleaner and more comfortable experience than toilet paper alone. Although the exterior of a bidet mixer faucet looks simple, its internal mechanism combines temperature regulation, flow control, directional adjustment, and spray mode optimization. Understanding how it works helps homeowners choose the right fixture and maintain it effectively. High-quality bidet faucets—such as those from COIGN’s bidet...
How Does the Bathtub Faucet Work?
A bathtub faucet may appear simple from the outside, but its internal mechanisms operate through coordinated water pathways, valves, pressure control, and flow direction systems. Understanding how it works helps homeowners make better decisions about installation, daily usage, and maintenance. Modern bathtub faucets combine mechanical precision with aesthetic design, and high-quality models—such as those from COIGN’s bathtub faucet collection—enhance water delivery, temperature stability, and...
How to Install a Freestanding Tub Faucet?
Installing a freestanding tub faucet is an essential step in completing the look and function of a standalone bathtub. Unlike wall-mounted or deck-mounted faucets, a freestanding faucet connects directly from the floor, creating a striking visual accent while delivering water in a clean, elegant way. Although the installation process is more detailed and requires careful preparation, following the correct steps ensures stability, leak-free performance, and long-term reliability. For homeowners...
How to Replace a Hand Held Shower Head and Hose?
Replacing a hand held shower head and hose is one of the most practical ways to improve shower comfort, increase water flow, and restore system efficiency. Over time, mineral deposits, aging rubber washers, and worn hose materials can affect performance. Fortunately, replacing these components is straightforward and requires only a few household tools. Whether you’re upgrading to a new style or solving a leaking issue, this guide provides an extremely detailed explanation of how removal and...
How Do You Install a Hand Held Shower Head?
Installing a hand held shower head is a simple upgrade that can dramatically improve shower flexibility and comfort. The process typically involves attaching a hose, connecting the shower head, and mounting the bracket. Most installations can be completed within minutes and do not require advanced plumbing skills. A well-designed hand held shower head — such as those offered by COIGN — ensures a smoother installation thanks to durable connectors, universal fittings, and stable mounting...
Contact
Send Inquiry
Related Products List
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.